{"product_id":"2-channel-ac110v-220v-radio-memory-remote-control-rf-receiver","title":"2 Channel AC110V\/220V Radio Memory Remote Control RF Receiver (Model 0020230)","description":"\u003cspan style=\"margin: 0px; padding: 0px; font-family: arial, helvetica, sans-serif; font-size: small;\" size=\"2\" face=\"arial, helvetica, sans-serif\"\u003e \u003cb\u003eFeature:\u003c\/b\u003e\u003cbr\u003e Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks, motors, fans, winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various devices.\u003cbr\u003e Wireless control, easy to install\u003cbr\u003e Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.\u003cbr\u003e Universal input: Support voltage of AC110V (100V~120V), widely used in US, Canada... and voltage of AC220V (200V~240V), used in UK, France...\u003cbr\u003e Relay Output: This receiver is relay output, it can be used to operate both DC and AC equipments. The terminal is NO \/ NC (normally open \/ normally closed), which serves as a switch. That means you should also connect a separate power supply to it.\u003cbr\u003e With manual terminals: The receiver allows you to connect external devices, sensors, or manual switches to control the receiver.\u003cbr\u003e With the external antenna, it can have a further working range.\u003cbr\u003e Use an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology. \u003cbr\u003e You can turn on\/ off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. \u003cbr\u003e With characteristics of reverse power protection and over current protection.\u003cbr\u003e Reliable control: The receiver only works with the transmitter which use same code.\u003cbr\u003e One\/several transmitters can control one\/several receivers simultaneously.\u003cbr\u003e You can use two or more units in the same place.\u003cbr\u003e With a transmitter (such as C-2) to form a complete set, the working distance can reach 100m in an open ground. The maximum working distance 100m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may or may not reach 100m. If you need longer range, please choose powerful transmitters, such as CB Series (1000m\/3000ft); or you can add the external antenna to the receiver for improving the range.\u003cbr\u003e \u003cbr\u003e \u003cb\u003eReceiver Parameters:\u003c\/b\u003e\u003cbr\u003e Model No.: S2MU-AC\u003cbr\u003e Power Supply (Operating Voltage): AC100~240V (110V\/120V\/220V\/240V)\u003cbr\u003e Working Frequency: 433MHz\u003cbr\u003e Channel: 2 CH\u003cbr\u003e Control Modes: Self-locking, Momentary, Interlocking, Momentary + Self-locking\u003cbr\u003e Output: Relay output (Normally open and normally closed)\u003cbr\u003e Working Voltage Range of Relay: AC110~240V or DC0~28V\u003cbr\u003e Maximum Working Current of Relay: 10A\u003cbr\u003e Static Current: ≤6mA\u003cbr\u003e Wire range：22~11AWG\u003cbr\u003e PCB size: 88mm x 80mm x 18mm\u003cbr\u003e Case size: 115mm x 90mm x 55mm\u003cbr\u003e Work with Fixed code transmitters or Learning code transmitters.\u003cbr\u003e The receiver can pair different model transmitters, includes model \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"https:\/\/www.wireless-remote-switches.com\/products\/2-button-100m-wireless-remote-control-transmitter-with-cover-model-0021001\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eC-2\u003c\/span\u003e\u003c\/a\u003e\u003c\/span\u003e\u003c\/strong\u003e \/ \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"https:\/\/www.wireless-remote-switches.com\/products\/3-button-100m-wireless-remote-control-transmitter-with-cover-model-0021002\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eC-3\u003c\/span\u003e\u003c\/a\u003e \u003c\/span\u003e\u003c\/strong\u003e (100M), \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"https:\/\/www.wireless-remote-switches.com\/products\/2-buttons-50m-wireless-remote-control-transmitter-waterproof-model-0021093\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eCWB-2\u003c\/span\u003e\u003c\/a\u003e \u003c\/span\u003e\u003c\/strong\u003e \/ \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"https:\/\/www.wireless-remote-switches.com\/products\/3-buttons-50m-wireless-remote-control-transmitter-waterproof-model-0021094\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eCWB-3\u003c\/span\u003e\u003c\/a\u003e\u003c\/span\u003e\u003c\/strong\u003e (50M, waterproof), \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"https:\/\/www.wireless-remote-switches.com\/products\/2-buttons-500m-wireless-remote-control-transmitter-model-0021011\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eCP-2\u003c\/span\u003e\u003c\/a\u003e\u003c\/span\u003e\u003c\/strong\u003e \/ \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"wireless-remote-switches.com\/products\/3-buttons-500m-wireless-remote-control-transmitter-for-motor-model-0021126\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eCP-3L\u003c\/span\u003e\u003c\/a\u003e \u003c\/span\u003e\u003c\/strong\u003e (500M) and \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"https:\/\/www.wireless-remote-switches.com\/products\/2-button-1000m-wireless-remote-control-transmitter-model-0021024\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eCB-2\u003c\/span\u003e\u003c\/a\u003e\u003c\/span\u003e\u003c\/strong\u003e \/ \u003cstrong\u003e\u003cspan style=\"color: #ff2a00;\"\u003e \u003ca href=\"https:\/\/www.wireless-remote-switches.com\/products\/3-button-1000m-wireless-remote-control-transmitter-model-0021025\" style=\"color: #ff2a00;\" target=\"_blank\"\u003e\u003cspan color=\"FF0000\"\u003eCB-3\u003c\/span\u003e\u003c\/a\u003e\u003c\/span\u003e\u003c\/strong\u003e (1000M) etc...\u003cbr\u003e If you want to have a further working range, you can install an external antenna to the receiver, such as magnetic mount antenna (model 0020909), which working range is three times as much as it used to be. Or telescopic antenna (model 0020918), which working range is twice as much as it used to be.\u003cbr\u003e \u003cbr\u003e \u003cb\u003eUsage (with the transmitter):\u003c\/b\u003e\u003cbr\u003e The receiver can be used to control both DC 0~28V and AC 110~240V equipments.\u003cbr\u003e Notice: The receiver is relay output, not DC\/AC power output. Initial state of relay output terminals: Terminals B and C are Normally Open; Terminals A and B are Normally Closed.\u003cbr\u003e \u003cbr\u003e If you want to control a DC 12V lamp, do as following:\u003cbr\u003e 1) Connect the live wire of the AC power supply to terminal “L \/ +”, and the neutral wire of the AC power supply to terminal “N \/ -“.\u003cbr\u003e 2) Connect terminal C to the positive pole of the DC power supply, connect terminal B to the positive pole of the DC lamp, and connect the negative pole of the DC lamp to the negative pole of the DC power supply.\u003cbr\u003e \u003cbr\u003e If you want to control an AC 220V lamp, do as following:\u003cbr\u003e 1) Connect the live wire of the AC power supply to terminal “L \/ +”, and the neutral wire of the AC power supply to terminal “N \/ -“.\u003cbr\u003e 2) Connect terminal C to the live wire of the AC power supply, connect terminal B to one side of the AC lamp, and connect another side of the AC lamp to the neutral wire of the AC power supply.\u003cbr\u003e \u003cbr\u003e \u003cb\u003eSetting different control modes \u003c\/b\u003e(We have set the receiver as Self-locking control mode before delivery. If you want to use other control modes, do as following operation):\u003cbr\u003e 1) Setting control mode Self-locking: Connect Jumper-2.\u003cbr\u003e Control mode Self-locking (with transmitter C-2): Press -\u0026gt; On; Press again -\u0026gt; Off.\u003cbr\u003e Press button 1: Turn on relay 1 (connect B and C, disconnect A and B)\u003cbr\u003e Press button 1 again: Turn off relay 1 (disconnect B and C, connect A and B)\u003cbr\u003e Press button 2: Turn on relay 2 (connect B and C, disconnect A and B)\u003cbr\u003e Press button 2 again: Turn off relay 2 (disconnect B and C, connect A and B)\u003cbr\u003e \u003cbr\u003e 2) Setting control mode Momentary: Connect Jumper-1.\u003cbr\u003e Control mode Momentary (with transmitter C-2): Press and hold -\u0026gt; On; Release -\u0026gt; Off.\u003cbr\u003e Press and hold button 1: Turn on relay 1 (connect B and C, disconnect A and B)\u003cbr\u003e Release button 1: Turn off relay 1 (disconnect B and C, connect A and B)\u003cbr\u003e Press and hold button 2: Turn on relay 2 (connect B and C, disconnect A and B)\u003cbr\u003e Release button 2: Turn off relay 2 (disconnect B and C, connect A and B)\u003cbr\u003e 3) Setting control mode Interlocking: Disconnect Jumper-1 and Jumper-2.\u003cbr\u003e Control mode Interlocking (with transmitter C-3): Press -\u0026gt; On, another relay Off; Press another button -\u0026gt; Off.\u003cbr\u003e Press button 1: Turn on relay 1 (connect B and C, disconnect A and B)\u003cbr\u003e Turn off relay 2 (disconnect B and C, connect A and B)\u003cbr\u003e Press button 2: Turn on relay 2 (connect B and C, disconnect A and B)\u003cbr\u003e Turn off relay 1 (disconnect B and C, connect A and B)\u003cbr\u003e 4) Setting control mode Momentary + Self-locking: Connect Jumper-1 and Jumper-2.\u003cbr\u003e Control mode Momentary (Channel 1): Press and hold -\u0026gt; On; Release -\u0026gt; Off.\u003cbr\u003e Press and hold button 1: Turn on relay 1 (connect B and C, disconnect A and B)\u003cbr\u003e Release button 1: Turn off relay 1 (disconnect B and C, connect A and B)\u003cbr\u003e Control mode Self-locking (Channel 2): Press -\u0026gt; On; Press again -\u0026gt; Off.\u003cbr\u003e Press button 2: Turn on relay 2 (connect B and C, disconnect A and B)\u003cbr\u003e Press button 2 again: Turn off relay 2 (disconnect B and C, connect A and B)\u003cbr\u003e \u003cbr\u003e \u003cb\u003eFunction of memory:\u003c\/b\u003e\u003cbr\u003e When the relay is on the status of \"ON\", it will shift to the status of \"OFF\" when the power is cut off.\u003cbr\u003e Once the power is restored, the relay will return automatically to the previous status of \"ON\".\u003cbr\u003e \u003cbr\u003e \u003cb\u003eManual control terminals:\u003c\/b\u003e\u003cbr\u003e The receiver has manual control terminals, you can connect external devices, sensors, or manual switches to control the receiver.\u003cbr\u003e 1) Signal input:\u003cbr\u003e You can connect external devices (with low level output signal) to terminals “1”, “3”, the external device’s output signal can control the receiver.\u003cbr\u003e When the external device outputs low level signal to terminal “1” and “3“, turn on the relay1 (connect terminals B and C, disconnect terminals A and B).\u003cbr\u003e When the external device does not output signal to terminal “1” and “3“, turn off the relay1 (disconnect terminals B and C, connect terminals A and B).\u003cbr\u003e You can connect external devices (with low level output signal) to terminals “2”, “3”, the external device’s output signal can control the receiver.\u003cbr\u003e When the external device outputs low level signal to terminal “2” and “3“, turn on the relay2 (connect terminals B and C, disconnect terminals A and B).\u003cbr\u003e When the external device does not output signal to terminal “2” and “3“, turn off the relay2 (disconnect terminals B and C, connect terminals A and B).\u003cbr\u003e \u003cbr\u003e 2) The manual switches:\u003cbr\u003e You can connect one manual switch to terminals “1”, “3”, and then you can use this manual switch to control the receiver.\u003cbr\u003e When connect terminals “1” and “3”, turn on the relay1 (connect terminals B and C, disconnect terminals A and B).\u003cbr\u003e And when disconnect terminals “1” and “3”, turn off the relay1 (disconnect terminals B and C, connect terminals A and B).\u003cbr\u003e You can connect one manual switch to terminals “2”, “3”, and then you can use this manual switch to control the receiver.\u003cbr\u003e When connect terminals “2” and “3”, turn on the relay2 (connect terminals B and C, disconnect terminals A and B).\u003cbr\u003e And when disconnect terminals “2” and “3”, turn off the relay2 (disconnect terminals B and C, connect terminals A and B).\u003cbr\u003e \u003c\/span\u003e","brand":"Receivers \/ Wireless Switches","offers":[{"title":"Default Title","offer_id":40404054114373,"sku":"","price":39.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0562\/1261\/9333\/products\/1_a4c55b77-8c0a-40e9-8d27-13203722969b.jpg?v=1666680197","url":"https:\/\/www.wireless-remote-switches.com\/products\/2-channel-ac110v-220v-radio-memory-remote-control-rf-receiver","provider":"Wireless Remote Switches Online Store","version":"1.0","type":"link"}