30A Large Load Dry Contact Relay Switch With Remote Control (Model 0020444)

Regular price $107.00

Shipping calculated at checkout.
Package Include:
1 x Receiver: S4PU-DC-ANT3
2× Transmitter: C-4
1× User Manual

Application:
This receiver is an electric device with 4 relay outputs, it and the transmitter form a wireless remote-control system. This system may be used in all types of industry automation, agriculture, business, home, factory, house, farm, garage, vehicle, ship, aerial vehicle, etc. It can remote control different DC or AC equipment on land, water, and air, such as lights, doors, windows, lamps, sockets, locks, sirens, outlets, heaters, motors, fans, winches, curtains, blinds, linear actuators, electric solenoid valves, and security alarm systems. The applications are endless.

Feature:
Wireless control, easy to install.
Super long working range: With the transmitter forming a complete set, the maximum working distance may reach 1000 meters in an open area.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Four operating voltage versions: DC 6V, 9V, 12V, 24V optional.
Relay Output: This receiver is dry relay output; it can be used to operate both DC and AC equipment. The output terminals are NO / NC (normally open / normally closed), serving as a switch. That means you should also connect a separate power supply to equipment.
High Power: Each channel can work at maximum load current 30A.
With wired control terminals: You can connect sensors, limit switches, manual switches, or external devices to control the receiver.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
Wireless RF signal from the transmitter can pass through walls, floors, doors, or windows, but it will lose some operating range.
The receiver has reverse voltage protection and overcurrent protection.
The receiver can only be triggered by paired transmitters.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.

Receiver Parameters:
Model: S4PU-DC-ANT3
Operating Voltage: 6VDC (model S4PU-DC06), or 9±1VDC (model S4PU-DC09), or 12±1VDC (model S4PU-DC12), or 24±2VDC (model S4PU-DC24), the operating voltage must be specified when ordering.
Working Frequency: 433.92 MHz
Quiescent Current: ≤6mA
Channel: 4 CH
Output Type: Dry Relays Output (With Normally Open and Normally Closed Terminals)
Maximum Load Voltage of Relay: 240VAC or 28VDC
Maximum Load Current of Relay: 30A / channel
Suitable Wires for Connecting Terminals: 22-12 AWG
4 Selectable Working Modes: Self-locking, Momentary, Interlocking, Momentary + Self-locking
Operating Temperature: -20 °C ~ +70 °C
PCB size: 170 x 100 x 18 mm (6.7x 4.0 x 0.7 inches)
Case size: 200 x 120 x 53 mm (7.9x 4.0 x 2.0 inches)

Transmitter Parameters:
Model: 0021003 (C-4)
Channel/Button: 4
Button Symbol: 1, 2, 3, 4
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 6mA
Operating Frequency: 433Mhz
Encoding Chip: PT2262 / PT2264 / SC2262
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 100m / 300ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 58 x 39 x 16 mm

Matching Transmitters:
The receiver can work with different transmitters, such as model CWB-4 (50M, waterproof), C-4 (100 meters / 300 feet range), CV-4 / CP-4 (500 meters / 1500 feet range) and CB-4 (1000 meters / 3000 feet range) etc

Working Range:
With a transmitter (such as C-4) to form a complete set, the maximum working distance can reach 300 feet or 100 meters in an open area.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no interference. But in the practice, it will be hindered by trees, walls, or other construction, and will be interfered by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.
If you need a longer working distance, you can replace the antenna on the receiver, or use an RF signal repeater, or use a powerful transmitter, such as a CB-4 transmitter.

Usage:
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.
Notice: The receiver is dry relay output, not DC/AC power output. Initial state of relay output terminals: Terminals <B> and <C> are Normally Open; Terminals <A> and <B> are Normally Closed.

Wiring:
1) If you want to control a DC 12V lamp, do as following:
1.1 Connect the live wire of AC power supply to terminal <L/+>, and connect the neutral wire of AC power supply to terminal <N/->.
1.2 Connect terminal <C> to the positive pole of DC power supply, connect terminal <B> to the positive pole of DC lamp, and connect the negative pole of DC lamp to the negative pole of DC power supply.

2) If you want to control an AC 220V lamp, do as following:
2.1 Connect the live wire of AC power supply to terminal <L/+>, and connect the neutral wire of AC power supply to terminal <N/->.
2.2 Connect terminal <C> to the live wire of AC power supply, connect terminal <B> to one side of AC lamp, and connect another side of AC lamp to the neutral wire of AC power supply.

Setting different control modes:
The receiver will be set in Self-locking mode before leaving the factory, if you want to use another mode, please follow the following steps.

1) Setting Momentary mode: Press the learning button in the receiver 2 times, signal LED continuously flashes 2 times and then goes off.
The operation of Momentary mode with the transmitter C-4:
Press and hold the button 1 on the transmitter: The relay 1 in the receiver is activated, and the connected lamp 1 is turned on.
Release the button 1: The relay 1 is deactivated, and the connected lamp 1 is turned off.
……
Press and hold the button 4 on the transmitter: The relay 4 in the receiver is activated, and the connected lamp 4 is turned on.
Release the button 4: The relay 4 is deactivated, and the connected lamp 4 is turned off.

2) Setting Self-locking mode: Press the learning button in the receiver 3 times, signal LED continuously flashes 3 times and then goes off.
The operation of Self-locking mode with the transmitter C-4:
Press the button 1 on the transmitter: The relay 1 in the receiver is activated, and the connected lamp 1 is turned on.
Press the button 1 again: The relay 1 is deactivated, and the connected lamp 1 is turned off.
……
Press the button 4 on the transmitter: The relay 4 in the receiver is activated, and the connected lamp 4 is turned on.
Press the button 4 again: The relay 4 is deactivated, and the connected lamp 4 is turned off.

3) Setting Interlocking mode: Press the learning button in the receiver 4 times, signal LED continuously flashes 4 times and then goes off.
The operation of Interlocking mode with the transmitter C-4:
Press the button 1 on the transmitter: The relay 1 in the receiver is activated, and the connected lamp 1 is turned on. Other 3 relays are deactivated, and other 3 connected lamps are turned off.
……
Press the button 4 on the transmitter: The relay 4 in the receiver is activated, and the connected lamp 4 is turned on. Other 3 relays are deactivated, and other 3 connected lamps are turned off.

4) Setting Momentary (Channel 1~2) + Self-locking (Channel 3~4) mode: Press the learning button in the receiver 5 times, signal LED continuously flashes 5 times and then goes off.

Wired control terminals:
The receiver has wired control terminals, and you can connect external devices, sensors, or manual switches to these terminals, then use them to control the receiver.
1) By low level signal:
You can connect the external devices (with low level output signal) to the terminal <Signal 1>, <Signal 2>, <Signal 3>, <Signal 4>, and the terminal <COM>, then use the external devices to control the receiver.
When the external device outputs low level signal to the terminals <Signal 1> and <COM>, the relay 1 in the receiver is activated, and the connected lamp 1 is turned on.
When the external device stops to output signal, the relay 1 is deactivated, and the connected lamp 1 is turned off.
When the external device outputs low level signal to the terminals <Signal 2> and <COM>, the relay 2 in the receiver is activated, and the connected lamp 2 is turned on.
When the external device stops to output signal, the relay 2 is deactivated, and the connected lamp 2 is turned off.
When the external device outputs low level signal to the terminals <Signal 3> and <COM>, the relay 3 in the receiver is activated, and the connected lamp 3 is turned on.
When the external device stops to output signal, the relay 3 is deactivated, and the connected lamp 3 is turned off.
When the external device outputs low level signal to the terminals <Signal 4> and <COM>, the relay 4 in the receiver is activated, and the connected lamp 4 is turned on.
When the external device stops to output signal, the relay 4 is deactivated, and the connected lamp 4 is turned off.

2) By NO/NC contact:
You can connect the manual switches (with NO/NC contact) to the terminals <Signal 1>, <Signal 2>, <Signal 3>, <Signal 4> and the terminal <COM>, then use the manual switches to control the receiver.
When connect the terminals <Signal 1> and <COM> by the manual switch, the relay 1 in the receiver is activated, and the connected lamp 1 is turned on.
When disconnect the terminals <Signal 1> and <COM> by the manual switch, the relay 1 is deactivated, and the connected lamp 1 is turned off.
When connect the terminals <Signal 2> and <COM> by the manual switch, the relay 2 in the receiver is activated, and the connected lamp 2 is turned on.
When disconnect the terminals <Signal 2> and <COM> by the manual switch, the relay 2 is deactivated, and the connected lamp 2 is turned off.
When connect the terminals <Signal 3> and <COM> by the manual switch, the relay 3 in the receiver is activated, and the connected lamp 3 is turned on.
When disconnect the terminals <Signal 3> and <COM> by the manual switch, the relay 3 is deactivated, and the connected lamp 3 is turned off.
When connect the terminals <Signal 4> and <COM> by the manual switch, the relay 4 in the receiver is activated, and the connected lamp 4 is turned on.
When disconnect the terminals <Signal 4> and <COM> by the manual switch, the relay 4 is deactivated, and the connected lamp 4 is turned off.