Usage of 4 way telephone wireless remote control module

Posted by CaryRS on

This telephone wireless remote control module is an electric device with 4 relay outputs. It can control variety of home appliances and electronic products in any place worldwide by fixed telephone or mobile phone. Such as remote control Lights, TVs, Motors, Fans, Cameras, Video/ Audio signals, Electrically operated Doors/ Locks/ Windows/ Curtains/ Bell or other equipments with voltage AC 110~240V or DC 0~48V.

Operation:
1) Input password:
Dial the telephone number of the phone line which the controller is connected, the telephone could be connected automatically after 6 ringing.
After entering the 4 - digit password continuously, press the "#" button to confirm. If the password is correct, it will prompt "DD" two sounds. If it is wrong, it will prompt "DDD" three sounds. If the password is entered incorrectly, you can press the "*" button to cancel, and then re-enter the 4-digit password. There are 10 opportunities to enter passwords in total. After 10 times, the host will hang up the phone after 9 beeps of "D", then you need to restart the operation of this controller. This function can prevent the phone from being occupied.

Note: When the controller is connected to the phone, the first password must be entered within 20 seconds, otherwise it will automatically hang up the phone after 20 seconds, and the delay will be 20 seconds each time the button is pressed.

2) The operation of controller:
After entering the 4-digit password correctly and pressing the "#" button to confirm, the controller will prompt "DD" two sounds, it means that the controller can start to operate.
Input 1: Turn on the channel 1, the indicator light 1 is on, and a "DD" beep will sound.
Input 2: Turn on the channel 2, the indicator light 2 in on, and a "DD" beep will sound.
Input 3: Turn on the channel 3, the indicator light 3 is on, and a "DD" beep will sound.
Input 4: Turn on the channel 4, the indicator light 4 is on, and a "DD" beep will sound.
Input 5: Turn off the channel 1, the indicator light 1 is off, and a "DDD" beep will sound.
Input 6: Turn off the channel 2, the indicator light 2 is off, and a "DDD" beep will sound.
Input 7: Turn off the channel 3, the indicator light 3 is off, and a "DDD" beep will sound.
Input 8: Turn off the channel 4, the indicator light 4 is off, and a "DDD" beep will sound.

Check the current working status:
When you need to check the current working status, first input 9, then input 1 or 2, 3, 4 to check the working status of four channels. For example, enter 91 to query the working status of the channel 1. If the channel 1 is on, there will be two prompts of "DD", and if the channel 1 is off, there will be three prompts of "DDD".
After the operation, press the "#" key to confirm, the controller will automatically hang up the phone after 4 sounds of "D".
If no key is pressed within 20 seconds, the controller will automatically hang up the phone after 9 sounds of "D".
If you do not press the "#" key to confirm, you can continue to input.

Setting the controller:
Need to enter 17 digits numbers continuously for setting, these 17 digits numbers are password, number of rings, working mode and working time.

17 digits numbers: 8888 (4-digit password) + 6 (number of rings) + 1 (channel 1 working mode) + 0 (channel 2 working mode) + 1 (channel 3 working mode) + 0 (channel 4 working mode) + 01 (channel 1 working time) + 00 (channel 2 working time) + 10 (channel 3 working time) + 00 (channel 4 working time)

1) First 4 digits numbers: a 4-digit password that needs to be entered when starting the controller, the default value is 8888.

2) The 5th digit number: number of rings. It is determined according to the maximum actual number of rings in the place, generally between 1 - 8, and the controller may not be able to connect the phone after exceeding.

3) Next 12 digits numbers: working mode and working time:

The first 4 digits numbers represent the working modes of the 4 channels respectively, and the following 8 digits numbers represent the working time of the 4 channels respectively.

Working mode: Each digit number represents the working mode of a channel, 1 is momentary mode, 0 is self-locking mode. For example, 1010 means channel 1 and channel 3 are momentary mode, and channel 2 and channel 4 are self-locking mode.

Working time: Each 2 digits numbers indicate the working time of a channel. For example, 10 means working time is 10 seconds.

When set to momentary mode, you need to set working time at the same time. If set to self-locking mode, you can set working time to 00.

By default, their working mode and working time is as follows,
The channel 1: momentary mode with 1 second, and it will automatically turn off after 1 second.
The channel 2: Self-locking mode.
The channel 3: momentary mode with10 seconds, and it will automatically turn off after 10 second.
The channel 4: Self-locking mode.

If you want to change this default setting, you need to enter 17 digits numbers to reset.
For example: If you want to set the password to 5678, the number of rings is 4 times, the channels 1, 2 and 3 are self-locking modes, and the channel 4 is momentary mode with 5 seconds, the 17 digits that need to be input are as follows:
5678 4 0 0 0 1 00 00 00 05

Two setting methods:
1) Method 1:
Firstly, power on the controller, then use a double crystal head phone cable to connect one end to a normal telephone, the other end to be inserted into the “Setting” socket of the controller, then press the “SET” button of the controller, and the "LL" light on the main board of the controller is always on, prompting "DD" twice, the controller enters the setting state, indicating that the 17 - digit numbers to be set can be input, and after continuously inputting 17 - digit numbers, press the “#” button to confirm. After confirming that there is no error, press “SET” button again to exit the setting state, and the "LL" light is off. If you make a mistake, you can press the "*" key to re-enter.

2) Method 2:
Connect the normally used telephone line to the “telephone” interface of the controller, and then use another phone that can be dialed to dial the phone connected to the controller. When there is the first ring back, press the “SET” button on the controller main board, the controller is connected to the phone, the “LL” light is on, and “DD” is prompted twice, which means that the controller is in the setting state. Enter the 17-digit numbers to be set, and press the "#" key to confirm after continuously inputting 17-digit numbers. After confirming that it is correct, press the “SET” button again to exit the setting state, and the “LL” light is off. (This method is recommended to be performed on the switch.)

Reset the controller to factory settings:
If the controller is abnormally controlled or the settings are wrong, the controller can be restored to the factory settings.
Operation: first power off the controller, wait for about 5~10 seconds, after the indicator lights on the controller are all off, press and hold the “SET” button on the controller, then power on the controller, and release the button after the “LL” light is on, and then the “LL” light is off, indicating that the factory setting has been restored.

Here is the link of the 4 way telephone wreless remote control module:

https://www.wireless-remote-switches.com/products/4-way-telephone-wireless-remote-control-module-model-0040008