Package Include:
1 x Receiver: S1FC-AC
1 x Transmitter / Remote Control: CA-3
1 x User manual
Introduction and Application:
This is a wireless remote switch kit that controls the forward and reverse rotation of AC motors. It includes an S1FC-AC receiver and a CA-3 transmitter. It can be used for roller shutters, rolling doors, projection screens, awnings, pumps, winches, conveyors, or other devices with AC motors. If you connect an AC motor to this receiver, you can operate the motor to rotate in positive or reversal direction by the remote control. You can connect two limit switches to the receiver and use them to stop the motor.
Key Features:
Wireless control, easy to install.
Universal Power Supply: 110~240VAC (110V/120V/220V/240V)
AC Power Output: It can control AC motors with a voltage range of 110~240V AC (e.g., AC motors with 110V, 120V, 220V, or 240V).
2 Selectable Working Modes: Momentary, Interlocking
With three manual buttons: You can control the motor by manual buttons.
With limit control terminals: You can connect sensors, limit switches or external devices to stop the motor.
Reliable Signal: RF signal can pass through walls, floors, doors, or windows, but it will lose some operating range.
Safety Features: Reverse voltage and overcurrent protection.
Interference: Two or more receivers may be used in the same area without interference.
Receiver S1FC-AC Parameters:
| Parameters | Detail |
|---|---|
| Operating Voltage | 110~240VAC (110V/120V/220V/240V) |
| Output Voltage | 110~240VAC (110V/120V/220V/240V) |
| Channel | 1 CH, can work with an AC motor |
| Working Frequency | 433.92 MHz |
| Rated Current | 5A, so motor's maximum starting current cannot exceed 5A. |
| 2 Selectable Working Modes | Momentary, Interlocking |
| Suitable Wires for Connecting Terminals | 22-14 AWG |
| Operating Temperature | -20 °C ~ +70 °C |
| Case size | 100 x 60 x 30 mm (4.0 x 2.4 x 1.2 inches) |
| Matching Transmitters | CQ-3-2 (50m) / C-3-2 (100m) / CA-3 (200m) / CP-3 / CG-3 (500m), or CB-3-2 (1000m) |
Transmitter CA-3 Parameters:
| Parameters | Detail |
|---|---|
| Operating Voltage | 12V (1 x 23A -12V battery, can be used for 12 months) |
| Channel / Button | 3 Channels with button symbols ▲, ■, ▼ |
| Operating Frequency | 433 Mhz |
| Encoding Chip | EV1527 |
| Transmitting Distance | 200m / 600ft (theoretically) |
| Unit Size | 120 x 45 x 18 mm (4.7 x 1.8 x 0.7 inches) |
Setting different working modes:
The receiver will be set in Interlocking mode before leaving the factory, if you require momentary mode, please follow the following steps.
Attention: Need to restart the receiver after changing the working mode.
1) Setting Interlocking mode: Do not short two pins.
Operation with CA-3 transmitter or receiver buttons:
Press button ▲ → Motor rotates in positive direction.
Press button ▼ → Motor rotates in reversal direction.
Press button ■ → Motor stops.
2) Setting Momentary mode: Short two pins with a shouted cap.
Operation with CA-3 transmitter or receiver buttons:
Hold button ▲ → Motor rotates in positive direction.
Release button → Motor stops.
Hold button ▼ → Motor rotates in reversal direction.
Release button → Motor stops.
Limit control terminals:
The receiver has limit control terminals, and you can connect external devices (with normally open contact), such as sensors, limit switches to limit terminals, then use them to stop the motor.
For example, you can connect a normally open limit switch to two terminals <UP>, and connect another normally open limit switch to two terminals <DOWN>.
When motor rotates in positive direction, if two terminals <UP> are connected, the motor will stop automatically.
When motor rotates in reversal direction, if two terminals <DOWN> are connected, the motor will stop automatically.