Package Include:
1 X Receiver: S4X-DC-ANT3
1 X Use manual
Introduction:
This receiver S4X-DC-ANT3 is an electric device with 4 channels DC power output, it and the transmitter form a wireless remote-control system. This system may be used in all types of industry automation, agriculture, business, home, factory, house, farm, garage, vehicle, ship, aerial vehicle, etc. It can remote control different DC equipment on land, water, and air, such as lights, doors, windows, lamps, sockets, locks, sirens, outlets, heaters, motors, fans, winches, curtains, blinds, linear actuators, electric solenoid valves, and security alarm systems. The applications are endless.
Key Features:
Wireless control, easy to install.
Waterproof Design: Receiver has waterproof case and waterproof connector for outdoor use.
DC 10~80V operating voltage range.
DC Power Output: It can control DC equipment with a voltage in the range of 10~80 VDC.
8 Different Control Modes: Self-locking, Momentary, Interlocking, and 5 Mixed modes.
With external antenna, the receiver has a farther working range.
Reliable Signal: RF signal can pass through walls, floors, doors, or windows, but it will lose some operating range.
Safety Features: Reverse voltage and overcurrent protection.
Interference: Two or more receivers may be used in the same area without interference.
One or more transmitters / remotes can control one or several receivers simultaneously.
Receiver S4X-DC-ANT3 Parameters:
| Parameters | Detail |
|---|---|
| Operating Voltage Options | 10~80V DC |
| Output Type | 10~80V DC same as input voltage |
| Channel | 4 CH |
| Working Frequency | 433.92MHz |
| Maximum Load Current | 10A / channel |
| 8 Different Control Modes | Self-locking, Momentary, Interlocking, and 5 Mixed modes |
| Suitable Wires for Connecting Terminals | 22-12 AWG |
| Operating Temperature | -20 Ā°C ~ +70 Ā°C |
| PCB size | 140 x 73 x 18 mm (5.5 x 2.9 x 0.7 inches) |
| Case size | 192 x 100 x 45 mm (7.6 x 4.0 x 1.8 inches) |
| Matching Transmitters | Can work with different transmitters, such as model C-4 (100M), CWB-4 (50M, waterproof), CP-4 / CV-4 (500M) and CB-4 (1000M) etc. |
Wiring:
If you want to control a DC 12V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal <+> of INPUT, and connect the negative pole of DC power supply to terminal <-> of INPUT.
2) Connect terminal <+> of OUT to the positive pole of DC lamp, and connect terminal <-> of OUT to the negative pole of DC lamp.
Setting different working modes:
The receiver will be set in Self-locking mode before leaving the factory, if you want to use another mode, please follow the following steps.
1) Setting Momentary mode: Press the learning button in the receiver 2 times, signal LED continuously flashes 2 times and then goes off.
Operation with C-4:
Hold button 1 ā The terminal <OUT1> of the receiver outputs DC power (lamp 1 ON)
Release button 1 ā The terminal <OUT1> of the receiver stops outputting (lamp 1 OFF)
ā¦ā¦
Hold button 4 ā The terminal <OUT4> of the receiver outputs DC power (lamp 4 ON)
Release button 4 ā The terminal <OUT4> of the receiver stops outputting (lamp 4 OFF)
2) Setting Self-locking mode: Press the learning button in the receiver 3 times, signal LED continuously flashes 3 times and then goes off.
Operation with C-4:
Press button 1 ā The terminal <OUT1> of the receiver outputs DC power (lamp 1 ON)
Press button 1 again ā The terminal <OUT1> of the receiver stops outputting (lamp 1 OFF)
ā¦ā¦
Press button 4 ā The terminal <OUT4> of the receiver outputs DC power (lamp 4 ON)
Press button 4 again ā The terminal <OUT4> of the receiver stops outputting (lamp 4 OFF)
3) Setting Interlocking mode: Press the learning button in the receiver 4 times, signal LED continuously flashes 4 times and then goes off.
Operation with C-4:
Press button 1 ā The terminal <OUT1> of the receiver outputs DC power (lamp 1 ON); Other 3 terminals stop outputting (other 3 lamps OFF)
ā¦ā¦
Press button 4 ā The terminal <OUT4> of the receiver outputs DC power (lamp 4 ON); Other 3 terminals stop outputting (other 3 lamps OFF)
4) Setting Momentary (Channel 1) + Self-locking (Channels 2~4) mode: Press the learning button in the receiver module 5 times, signal LED continuously flashes 5 times and then goes off.
5) Setting Momentary (Channels 1~3) + Self-locking (Channel 4) mode: Press the learning button in the receiver module 6 times, signal LED continuously flashes 6 times and then goes off.
6) Setting Momentary (Channels 1~2) + Self-locking (Channel 3~4) mode: Press the learning button in the receiver module 7 times, signal LED continuously flashes 7 times and then goes off.
7) Setting Momentary (Channels 1~2) + Interlocking (Channel 3~4) mode: Press the learning button in the receiver module 8 times, signal LED continuously flashes 8 times and then goes off.
8) Setting Self-locking (Channels 1~2) + Interlocking (Channel 3~4) mode: Press the learning button in the receiver module 9 times, signal LED continuously flashes 9 times and then goes off.