Outdoor Wireless Waterproof Switch with European Standards Plug & Socket (Model 0020717)

Regular price $38.00

Shipping calculated at checkout.
Application:
This is a wireless remote switch with IP44 rated European standard plug and socket. You can use it to easily convert an ordinary AC power outlet into a wireless remote control switch. It can be used for remote control of lights, pumps, fans, motors, heaters, electric solenoid valves, alarms, and other AC equipment.

Feature:
Wireless control, easy to install.
Waterproof: The switch has waterproof case and waterproof connector; it can be installed outdoors.
Universal input: Support 110V AC (110V~120V) used in US, Canada, etc, and 220V AC (220V~240V) used in Germany, UK, France, etc.
AC Power Output: It can control AC equipment with voltage AC 110V, 120V, 220V or 240V.
High Power: It can work at maximum current 16A, such as 3500W/220V.
With wired control terminals: You can connect sensors, limit switches, manual switches, or external devices to control the wireless switch.
The transmitter / remote can control the wireless switch from any place within a reliable working distance.
Wireless RF signal from the transmitter can pass through walls, floors, doors, or windows, but it will lose some operating range.
With overcurrent protection.
The wireless switch can only be triggered by paired transmitters.
One or more transmitters / remotes can control one or several wireless switches simultaneously.
Two or more wireless switches may be used in the same area.

Wireless Switch Parameters:
Model: S1PX-EU-AC220
With European Standards Plug and Socket.
IP rating of plug and socket: IP44
Cable standard: three cores, 1.5 square millimeters
Input / Output: AC110~240V (110V/120V/220V/240V)
Working Frequency: 433.92MHz
Static Current: ≤6mA
Maximum Load Current of Relay: 16A
3 Selectable Working Modes: Self-locking, Momentary, Interlocking
Operating Temperature: -20 °C ~ +70 °C
PCB size: 90 x 59 x 18 mm (3.5 x 2.3 x 0.7 inches)
Case size: 100 x 68 x 50 mm (3.9 x 2.7 x 2.0 inches)
IP rating of waterproof case: IP65

Matching Transmitters:
This wireless switch can work with different transmitters, such as model C-1 / C-2 (100M), CWB-1 / CWB-2 (50M, waterproof), CP-1 / CP-2 (500M), or CB-1 / CB-2 (1000M) etc.
1) When you set wireless switch in self-locking or momentary mode, it should work with single button transmitter, such as model C-1 (100M), CWB-1 (50M, waterproof), CP-1 (500M), or CB-1 (1000M) etc.
2) When you set wireless switch in interlocking mode, it should work with two buttons transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), or CB-2 (1000M) etc.

Working Range:
With a transmitter (such as CWB-2) to form a complete set, the maximum working distance may reach 150 feet or 50 meters in an open area.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no interference. But in the practice, it will be hindered by trees, walls, or other construction, and will be interfered by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.
If you want to have a further working range, you can install an external antenna to wireless switch, and you also can use a powerful transmitter, such as CB series transmitters.

Usage:
Wireless switch can be used to control AC 110~240V (110V/120V/220V/240V) equipment.

Wiring:
If you want to control an AC 220V exhaust fan, do as following:
Plug the exhaust fan into the socket of this switch, and connect the plug of this switch to the AC 220V power supply.

Setting different working modes:
The wireless switch will be set in Interlocking mode before leaving the factory, if you want to use another mode, please follow the following steps.

1) Setting Self-locking mode: Only short pin 2.
The operation of Self-locking mode with the transmitter CWB-1:
Press the button on the transmitter: The wireless switch output AC power, and the exhaust fan works.
Press the button again: The wireless switch stop outputting, and the exhaust fan stops.

2) Setting Momentary mode: Only short pin 1.
The operation of Momentary mode with the transmitter CWB-1:
Press and hold the button on the transmitter: The wireless switch output AC power, and the exhaust fan works.
Release the button: The wireless switch stop outputting, and the exhaust fan stops.

3) Setting Interlocking mode: Do not short two pins.
The operation of Interlocking mode with the transmitter CWB-2:
Press the button A on the transmitter: The wireless switch output AC power, and the exhaust fan works.
Press the button B on the transmitter: The wireless switch stop outputting, and the exhaust fan stops.

Wired control terminals:
The wireless switch has wired control terminals, and you can connect external devices, sensors, or manual switches to these terminals, then use them to control the wireless switch.
1) By low level signal:
You can connect the external devices (with low level output signal) to the terminal 1 (Signal-) and the terminal 2 (Signal+), then use the external devices to control the wireless switch.
When the external device outputs low level signal to the terminals 1 and 2, the wireless switch output AC power, and the exhaust fan works.
When the external device stops to output signal, the wireless switch stop outputting, and the exhaust fan stops.

2) By NO/NC contact:
You can connect the manual switches (with NO/NC contact) to the terminals 1 and 2, then use the manual switches to control the wireless switch.
When connect the terminals 1 and 2 by the manual switch, the wireless switch output AC power, and the exhaust fan works.
When disconnect the terminals 1 and 2 by the manual switch, the wireless switch stop outputting, and the exhaust fan stops.

How to pair the transmitter to the wireless switch:
Notice: We have paired the transmitter to the wireless switch before leaving the factory.
1) Press the learning button in the wireless switch for 1-2 seconds, signal LED on the wireless switch turns on, this indicates that the wireless switch enters the learning status.
2) Press any one button on the transmitter, if signal LED flashes quickly 15 times and turns off, this indicates that the pairing is successful.
3) When wireless switch is in the learning status, press again the button in wireless switch, signal LED turns off, learning process will be discontinued.
4) The wireless switch can learn several transmitters with different codes.

How to delete all transmitters codes stored in the wireless switch:
We have paired the transmitter to the wireless switch, if you don’t want the wireless switch to work with the transmitter, you can delete all transmitters codes stored in the wireless switch.
Operation: Press and hold the learning button in the wireless switch, until signal LED flashes slowly; release the button, signal LED keeps slow flash, this indicates that all stored codes have been deleted successfully.