Package Include:
1 X Wireless Switch: S1PX-US-WP2-AC120 (with US Standards Plug & Socket)
1 X Transmitter: CP-2
1 X Use manual
Introduction:
This is a wireless remote switch kit with American standards plug and IP66 waterproof socket. It including a S1PX-US-WP2-AC120 wireless switch and a CP-2 transmitter. You can use it to easily convert an ordinary AC power outlet into a wireless remote control switch. It can be used for remote control of lights, pumps, fans, motors, heaters, electric solenoid valves, alarms, and other AC equipment.
Key Features:
Wireless control, easy to install.
Working Range: Up to 500m (15,00 ft) in open areas.
Waterproof: With IP65 waterproof case, waterproof connector and IP66 waterproof Socket
Universal input: Support 110V AC (100V~120V) used in US, Canada, etc.
AC Power Output: It can control AC equipment with voltage AC 110V, 120V.
High Power: It can work at maximum current 15A.
3 Selectable Working Modes: Self-locking, Momentary, Interlocking.
Reliable Signal: RF signal can pass through walls, floors, doors, or windows, but it will lose some operating range.
Safety Features: Reverse voltage and overcurrent protection.
Interference: Two or more wireless switches may be used in the same area without interference.
Wireless Switch S1PX-US-WP2-AC120 Parameters:
Transmitter CP-2 Parameters:
Setting different working modes:
The receiver will be set in Self-locking mode before leaving the factory, if you want to use another mode, please follow the following steps.
1) Setting Momentary mode: Press the wireless switch’s RF module learning button twice, signal LED flashes twice then goes off.
If you want to control an AC 120V exhaust fan with CP-1:
Hold button → Wireless switch output AC power (exhaust fan works)
Release → Wireless switch stop outputting (exhaust fan stops)
2) Setting Self-locking mode: Press the wireless switch’s RF module learning button 3 times, signal LED flashes 3 times then goes off.
If you want to control an AC 120V exhaust fan with CP-1:
Press once → Wireless switch output AC power (exhaust fan works)
Press again → Wireless switch stop outputting (exhaust fan stops)
3) Setting Interlocking mode: Press the wireless switch’s RF module learning button 4 times, signal LED flashes 4 times then goes off.
If you want to control an AC 120V exhaust fan with CP-2:
Press Button A → Wireless switch output AC power (exhaust fan works)
Press Button B → Wireless switch stop outputting (exhaust fan stops)
1 X Wireless Switch: S1PX-US-WP2-AC120 (with US Standards Plug & Socket)
1 X Transmitter: CP-2
1 X Use manual
Introduction:
This is a wireless remote switch kit with American standards plug and IP66 waterproof socket. It including a S1PX-US-WP2-AC120 wireless switch and a CP-2 transmitter. You can use it to easily convert an ordinary AC power outlet into a wireless remote control switch. It can be used for remote control of lights, pumps, fans, motors, heaters, electric solenoid valves, alarms, and other AC equipment.
Key Features:
Wireless control, easy to install.
Working Range: Up to 500m (15,00 ft) in open areas.
Waterproof: With IP65 waterproof case, waterproof connector and IP66 waterproof Socket
Universal input: Support 110V AC (100V~120V) used in US, Canada, etc.
AC Power Output: It can control AC equipment with voltage AC 110V, 120V.
High Power: It can work at maximum current 15A.
3 Selectable Working Modes: Self-locking, Momentary, Interlocking.
Reliable Signal: RF signal can pass through walls, floors, doors, or windows, but it will lose some operating range.
Safety Features: Reverse voltage and overcurrent protection.
Interference: Two or more wireless switches may be used in the same area without interference.
Wireless Switch S1PX-US-WP2-AC120 Parameters:
| Parameters | Detail |
|---|---|
| Input / Output Type | AC100~120V (110V/120V) |
| Plug and Socket Standards | with American Standards Plug and Waterproof Socket |
| IP Rating of Plug and Socket | IP66 |
| Cable Standard | three cores, 1.5 square millimeters |
| Load Capacity | 15A / channel |
| 3 Selectable Working Modes | Self-locking, Momentary, Interlocking |
| Suitable Wires for Connecting Terminals | 22-12 AWG |
| Operating Temperature | -20 °C ~ +70 °C |
| Wireless Switch Case Size | 100 x 68 x 50 mm (3.9 x 2.7 x 2.0 inches) |
| Socket Case Size | 110 x 110 x 96 mm (4.3 x 4.3 x 3.8 inches) |
| Matching Transmitters |
CWB-1(50m)
/
C-1(100m)
/
CP-1(500m)
/
CB-1(1km)
for Self-locking / Momentary CWB-2(50m) / C-2(100m) / CP-2(500m) / CB-2(1km) for Interlocking |
Transmitter CP-2 Parameters:
| Parameters | Detail |
|---|---|
| Operating Voltage | 12V (1 x 23A -12V battery, can be used for 12 months) |
| Operating Frequency | 433.92 Mhz |
| Transmitting Distance | 500m / 1500ft (theoretically) |
| Unit Size | 85 x 36 x 16 mm (3.3 x 1.4 x 0.6 inches) |
Setting different working modes:
The receiver will be set in Self-locking mode before leaving the factory, if you want to use another mode, please follow the following steps.
1) Setting Momentary mode: Press the wireless switch’s RF module learning button twice, signal LED flashes twice then goes off.
If you want to control an AC 120V exhaust fan with CP-1:
Hold button → Wireless switch output AC power (exhaust fan works)
Release → Wireless switch stop outputting (exhaust fan stops)
2) Setting Self-locking mode: Press the wireless switch’s RF module learning button 3 times, signal LED flashes 3 times then goes off.
If you want to control an AC 120V exhaust fan with CP-1:
Press once → Wireless switch output AC power (exhaust fan works)
Press again → Wireless switch stop outputting (exhaust fan stops)
3) Setting Interlocking mode: Press the wireless switch’s RF module learning button 4 times, signal LED flashes 4 times then goes off.
If you want to control an AC 120V exhaust fan with CP-2:
Press Button A → Wireless switch output AC power (exhaust fan works)
Press Button B → Wireless switch stop outputting (exhaust fan stops)